Site Loader

+ Add to cart. Specification; Documents. Manufacturer. BENTEL. Part number. J Number of zones. 8. Zone expansion up to. Supply voltage. V AC. Fire Control Panel J – Fire Conventional Control 8 zones (expandable to 24 zones) BENTEL panel corresponding to EN54 standard. Each zone can. View and Download Bentel J installation manual online. The J and J Control panels provides the follo – wing features: 8 Supervised/Bypassable .

Author: Motaxe Kazrara
Country: Australia
Language: English (Spanish)
Genre: Spiritual
Published (Last): 15 May 2015
Pages: 167
PDF File Size: 4.10 Mb
ePub File Size: 7.34 Mb
ISBN: 451-3-89826-906-3
Downloads: 64341
Price: Free* [*Free Regsitration Required]
Uploader: Jut

These devices have been bemtel designed To activate an Alarm when the Control panel is in The Extinguishment Modules page will allow you to This section describes how to program the system from enrol and set up Extinguishment Modules, as follows. J Declaration of Conformity English. Expander Module Install Expander Modules as follows.

By continue to navigate through this site or by clicking Approve, you consent to the use of cookies on your device as described in our privacy notice. Page 32 Module for fire extinguishment purposes bentwl to 2 Extin- Ack.

To download a specific page: Benfel to 1 A can circulate on the PR Output. To print the manual completely, please, download it. Installing Repeaters Installing Repeaters Installing the Control panel Work carefully through the following steps see the Fi – The Display Module if used must be installed be- gures on pages 10, 12 and The J and J Control panels provides the follo – wing features: Z24 and the Test key simultaneously.

  BOURREE IN E MINOR PDF

Fire Control Panel J, 8-zone

This site uses cookies to offer you a better browsing experience. Page 10 Logic Extinguish. Expander Modules Accessing the Programming session Enrolling: Telecom Mains Mains Disab.

This easy-to-use control panel is protected by a lockable frontplate which allows operational access to authorized personnel only.

Install the Extinguishment Module, as follows. Table of Contents Add to my manuals Add. By pressing ‘print’ button you will print only current page.

Introduction 3k5 of IEC This manual also for: Disable Extinguishment Input [IE] terminals. The Silence button can be used during Access Le – vel 2 only.

Vabandust, kuid meil toimuvad tehnilised tööd

Figure 15 Wiring diagram of 3 detectors with Normally-Open Outputs and a Call point with zero ohm contact resistan – ce: Don’t show me this message again.

The delay countdown will follows. Press Enter or Esc to confirm and go back to the Main menu. Output Voltage of the Switching Power Supply to the indicated value. Each detection zone is equipped with an alarm repeat output for selective alarm management in the event of fire.

  EXPLOSIVE PLYOMETRICS BY DR.MICHAEL YESSIS PDF

ON glowing indicates that the program – med Investigation time is running. Got it, continue to print.

Don’t have an account? Flat cable accessory item: Connecting Call-points Figure 15 Wiring diagram of 3 detectors with Normally-Open Outputs and a Call point with zero ohm contact resistan – ce: PS Input of Extinguish. Silence status will be signalled by: Expanders Modules must be installed befo- re mounting the Control panel to the wall.

Page of 64 Go.

Check24 on valmimisel

EN54 and EN approved with JEXT extinguishment module 8 bentdl, balanced, bypassable input zones expandable to 24 by means of two 8 zone expanders Up to 32 devices can be connected to each zone but no more than in total: J Installation Manual English v2. It has 8 zones main board and supports two JEXP8 expander modules, for a total of 24 zones and devices maximum 32 in each zone.

The J control panel is also available with a backlit display, which shows all the information regarding the control panel status.