Site Loader

Designation: B /B M – Standard Specification for. Aluminum Bronze Rod, Bar, and Shapes1 This standard is issued under the fixed designation B. Chemical Composition according to ASTM B/BM(). 1Cu value includes Ag. %emsp;2Ni value includes Co. Note: Cu + Sum of Named Elements, . ASTM B/BM(). Standard Specification for Aluminum Bronze Rod, Bar, and Shapes. standard by ASTM International, 04/01/ View all product.

Author: Karr Kigakora
Country: Burma
Language: English (Spanish)
Genre: Software
Published (Last): 22 March 2013
Pages: 319
PDF File Size: 14.65 Mb
ePub File Size: 2.52 Mb
ISBN: 541-1-48266-544-5
Downloads: 49965
Price: Free* [*Free Regsitration Required]
Uploader: Samuk

C HR50 rod round only: Work Item s – proposed revisions of this standard. Dimensions, Mass and Permissible Variations In any case, a minimum gage length of 1 in. NOTE 4—A residual stress test provides information about the adequacy of the stress relief of the material. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn.

When the product is for subsequent welding applications and is so specified by the purchaser, chromium shall be 0. Historical Version s – view previous versions of standard. Committee B05 has identified the location of selected changes to this standard since the last issue B — 98e2 that may impact the use of this standard. Products should also meet requirements under mercurous nitrate test, ammonia test, and piston finish. This standard has been approved for use by agencies of the Department of Defense.

ASTM B150 & B150M -03

See Ordering Information and Other Requirements sections. We are a non-profit group that run this website to share documents. C HR50 drawn and stress relieved M20 M30 O20 O25 O30 HR50 as hot rolled as hot extruded hot forged and annealed hot rolled aetm annealed hot extruded and aatm drawn and stress relieved HR50 drawn and stress relieved M20 M30 O20 O25 O30 HR50 as hot rolled as hot extruded hot forged and annealed hot rolled and annealed hot extruded and annealed drawn and stress relieved M20 M30 O20 O25 O30 HR50 as hot rolled as hot extruded hot forged and annealed hot rolled and annealed hot extruded and annealed drawn and stress relieved HR50 drawn and stress relieved TQ50 h150 hardened and temper annealed O32 hot extruded and temper annealed TQ30 quenched hardened and tempered 6 6 6 6 1—standard strength rod: The alloy has a proven history within Naval applications where it is used extensively in the building of Nuclear submarines and other Naval surface craft.

  AMBA AXI PROTOCOL PDF

It is a heat treated alloy that is a strong, corrosion resistant material that performs well at high and low temperatures, C also has a low magnetic permeability making it ideal for instrumentation systems. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Thank you for interesting in our services. C TQ50 quench hardened and temper annealed TQ55 quench hardened, temper annealed, drawn, and stress relieved O20 O25 hot forged and annealed hot rolled and annealed 6 J rod and bar: By agreement between the manufacturer and the purchaser, limits may be established and analysis required for unnamed elements. Stress relief annealing is a method of thermal stress relief. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

See Table 14.

Current edition approved April 15, C Yield strength at 0. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their b1550 responsibility. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Materials and Manufacture 5.

In addition, the alloy has excellent wear resistance and good corrosion resistance in fresh and sea water. In any case, a minimum gage length of 1 in. Originally approved in We need your help! With the Mercurous Nitrate Test, equipment for the detection and removal of mercury vapor produced in volatilization, and the use of protective gloves is recommended. C Chromium shall be 0.

  GRO STEINSLAND PDF

When the product is for subsequent welding applications and is so speci? ASTM D – Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. A superscript epsilon e indicates an editorial change since the last revision or reapproval. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Approved May 10, B and B M were combined. Approved April 15, Link to Active This link will always route to the current Active version of the standard. Mercury, or its vapor, may be hazardous to health and corrosive to materials.

ASTM B / BM – 12() Standard Specification for Aluminum Bronze Rod, Bar, and Shapes

The new b10 alloy has a quench and temper heat treatment which eliminated this problem introducing a structure that changed the morphology of the kappa phase. C and C HR50 drawn and stress relieved rod and bar: Materials and Manufacture 5. Get a Quote for Aluminum Bronze C Stainless Steel H Aluminum Silicon Bronze C Please fill this form, we will try to respond as soon as possible.

C is specified, the tolerances for diameter, thickness, width, and length shall be part of the contract or purchase order and shall be agreed upon between the supplier and the purchaser. C Chromium shall be 0. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.