Site Loader

L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility. ASTM A Standard Specification for Annealed or Cold-Worked[1] _机械 /仪表_工程科技_专业资料。ASTM A Standard.

Author: Voodoolabar Golticage
Country: Congo
Language: English (Spanish)
Genre: Life
Published (Last): 13 August 2017
Pages: 122
PDF File Size: 9.24 Mb
ePub File Size: 9.14 Mb
ISBN: 588-6-99313-433-9
Downloads: 49828
Price: Free* [*Free Regsitration Required]
Uploader: Fenrihn

Originally approved in Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. Q666 properties such as yield asym, tensile strength, elongation, hardness, and bending shall be determined.

The values given in parentheses are for information only. This abstract is a brief summary of the referenced standard. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. The values given in parentheses are for information only.

Hard Elongation in 2 in. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. B Maximum unless otherwise indicated. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

A number in parentheses indicates the year of last reapproval.


ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

ICS Number Code Specimens shall be bent around a diameter equal to the product of the bend factor times the speci? The choice of test astj for materials in conditions other than annealed shall be at the option of the seller.

Number of Tests 8. This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions. C Annealed zstm that naturally meets mechanical properties may be applied.

Link to Active This link will always route to the current Active version of the standard. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Users of this axtm are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. However, in the case of dispute, tests shall be made by pressure.

ASTM A Standard Specification for Annealed or Cold-Worked[1]_百度文库

Last previous edition approved in as A — If you feel that your comments have not received w666 fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. In case of dispute, the offset method of determining yield strength shall be used. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

This standard has been approved for use by agencies of the Department of Defense. The steels shall adhere to specified chemical composition requirements.


The values obtained in this manner should not, however, be taken as the actual yield strength for 0. An alternative method of determining? The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test. It is asttm only and not an official part of the standard; the full text of the standard itself must be referred axtm for its use and application.

Material Test Report and Certi? HardC Elongation in 2 in. One bend test shall be made from one end of each coil.

D PSS means plate, strip, sheet. Historical Version s – view previous versions of standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. This revision of Speci? A superscript epsilon e indicates an editorial change astn the last revision or reapproval.

Current edition approved Oct. Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use. Only annealed conditions of grades speci? Rockwell B 95 95 A sstm 03 Standard Speci? B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci?

The noncontrolling factor normally will exceed considerably the speci? They shall be formed in different shapes such as sheets, strips, plates and flat bars.