Site Loader

(This Information Sheet is NOT an AGMA Standard). American Gear Metallurgical Specifications for Steel Gearing Manufacturers AGMA B05 CAUTION. (This Information Sheet is NOT an AGMA Standard). American Gear Metallurgical Specifications for Steel Gearing Manufacturers AGMA B05 Association. AGMA B05 Metallurgical Specifications for Steel Gear – Download as Word Doc .doc /.docx), PDF File .pdf) or read online. AGMA B05 Metallurgical.

Author: Sharg Tahn
Country: Russian Federation
Language: English (Spanish)
Genre: Life
Published (Last): 5 October 2004
Pages: 28
PDF File Size: 5.54 Mb
ePub File Size: 13.25 Mb
ISBN: 223-5-88008-234-3
Downloads: 43811
Price: Free* [*Free Regsitration Required]
Uploader: Kigalar

At the time of initial development, the editions shown were valid.

Gear Design Relevant Cleanness Metrics

Grade 2 Test report only. Key terms used in this document are defined as follows: Heat Treatment of Steel Gears July 15, For nitriding specifications surface hardness is typically used rather than case hardness. Banding – See microsegregation.

Total case depth in finished Minimum total case depth requirements for the tooth should be specified in accordance with condition the appropriate rating standard. More precise measurements of retained austenite can be obtained by X–ray diffraction techniques.

Carbide precipitation in the Continuous carbide case. This standard is not included in any packages. Both methods 923–b05 that prior to carburizing the process control specimen, sufficient stock be machined from the surface to be carburized, in order to aga all material with non–uniform surface chemistry. This paper has illustrated how statistically robust inclusion population afma, gathered with SEM automated image analysis, can generate the statistically rich data needed to robustly consider design concerns.

The tooth area includes only those portions of the gearing material where the teeth will be located to a depth below the finished tooth tips of at least 1. Further evaluation at higher magnifications shown in the progression of pictures moving forward to the right shows a fatigue thumbnail, and in the middle of the thumbnail is a 293-b05 oxide micro inclusion that measures approximately 20 mm in square root area.

  BD131 DATASHEET PDF

See specific kind of hardness such as base, case, core or surface. A surface hardening process in which only the surface layer of the work piece is 92-b05 by electrically induced currents to above the upper transformation temperature and immediately quenched. Figure 14 Type A contour pattern only shall be specified. While stringers do tend to be larger and therefore more injurious when present in a critically loaded location, it is much more probable that an injurious micro inclusion will be located in a critical location compared to a stringer.

Metallography – Performed at a magnification of — diameters. Suggestions for improvement of this standard will be welcome.

[PDF] AGMA B05 – Free Download PDF

Falk Corporation Xtek, Inc. Standards Subsctiption may be the perfect solution. The loss of carbon from the near–surface of a ferrous material. A measure of the ability of a furnace environment containing active carbon to alter or maintain, under prescribed conditions, the carbon content of the steel. Individual AGMA rating standards may have specific modifications to the metallurgical characteristics grading; but the intent is to formalize agmz assumptions and definitions on which the various AGMA standards are based.

The various characteristics are listed in the wgma in which that characteristic is typically evaluated during the manufacturing sequence. A cold working process performed by bombarding the surface of a part with small spherical media.

AGMA 923-B05

Grade 1 Not abma. TimkenSteel can produce any of its grades to this new steel micro-cleanness standard. The minimum acceptable requirements for each factor for metallurgical quality Grades 1, 2 and 3 are specified. Figure 3 a shows the raw data from automated SEM image ahma in the form of a histogram for micro globular oxide inclusion 923-v05 square millimeter.

  CHORTI VOCABULARIO PDF

A heat treatment process in which an austenitized steel is brought into contact with a carbonaceous atmosphere of sufficient carbon potential to cause adsorption of carbon at the surface and by diffusion to create a concentration gradient. The gear rating may be limited by either pitting resistance or bending strength for the selected metallurgical quality grade and its core hardness requirement.

Similarly, volumetric inclusion populations can be used to populate loading models, in combination with Monte Carlo simulation, to aga relative fatigue life between different abma. Due to the tooth section size of 3 normal diametral pitch 8 module gearing and coarser, the alternate ISO core hardness test location may be used provided documented testing or experience is available.

Metallurgical characteristics for carburize and hardened gearing. The section size which has the greatest effect in determining the rate of cooling during quenching at a location where the specified hardness is required. Intergranular oxidation IGO Not specified. However, properly selected test coupons can also be used. Care must be taken when grinding nitrided surfaces to ensure that no harmful surface conditions are produced in the grinding process.

This zone can have lower hardness and different microstructure than the base material.